Goulds
-
Pool Supply Delivery Goulds 1.5 HP 1 Phase 115-230V Centrifugal Self-Priming Pump - GT15
Goulds GT15 1.5 Horsepower 1 Phase 115/230V Centrifugal Self-Priming Pump is designed so that once the pump is primed it never needs priming again, even if water level drops below the end of the suction pipe. Pumping resumes once the water level rises above the end of the suction pipe. Specifically designed for lawn sprinkling, irrigation, air conditioning systems, heat pumps, water transfers and dewatering. Pump body has a cast iron casing, stainless steel ring for longer life and resistance to wear with F.D.A. compliant impeller. Application: Water Systems Features: Shaft: Uses Motor shaft, 300 Series Stainless Steel Shaft Seal: Standard Mech. Seal is Buna/Carbon/Ceramic/S.S, Casing "O"-Ring is Buna Ports: 1-1/2" NPT Inlet x 1-1/2" NPT Discharge
$607.99
-
Pool Supply Delivery Goulds 1 HP 230V CentriPro Quick Disconnect (QD) Control Box - CB10412
Goulds CB10412 1.0 Horsepower 230V CentriPro control boxes feature voltage relays for installer convenience, start capacitors and a quick disconnect cover design that will retrofit with F.E. Q-D control boxes.
$103.99
-
Pool Supply Delivery Goulds 3 HP 230V CentriPro CSCR Control Box - CB30412CR
Goulds CB30412CR 3.0 Horsepower 230V CentriPro CSCR Control Box features voltage relays for installer convenience with run capacitors for efficiency and quiet operation. Features: 230 volt models – 208 volt relay, 9K479, available for low voltage applications Start Capacitors for starting torque Type 3R enclosure for indoor or outdoor mounting Accepts up to #2 AWG wire Multiple knockouts and two ground terminals Higher HP models require heavy duty pressure switches – See Magnetic Contactor version to use standard pressure switches Manual reset overloads on 1½ – 5 HP models
$295.99
-
Goulds Goulds 4/10 HP 115V 1 Phase Sink Drain System - SDS1
Goulds SDS1 4/10 Horsepower 115V 1 Phase Sink Drain System is a sink drain package specifically designed for the following uses: Laundry tray, Wet bar sink, Air conditioning condensate or Dehumidifier water, Residential dishwashers or Beautician sink. Features: Fully Assembled – Individually Cartoned. Capable of Running Dry without Damage to Components. Severe Duty Rated Oil and Water Resistant Power Cable. Specifications: 0.4 HP, 115 V, 1 PH, 1550 RPM, with 10' cord Maximum Amps: 12. • ¾" maximum solids handling. Capacities: up to 55 GPM. Total heads: up to 24 feet. Built in overload with automatic reset. Assembled Components: EP0411, 0.4 HP, ¾" solids handling pump is CSA listed. CSA listed pump A2H11 Vertimaster vertical level switch with 10 foot cord and piggyback plug is UL and CSA listed. 10 gallon structural foam basin and cover. 1½" NPT threaded vent, discharge and inlet connections. 1½" schedule 40 PVC discharge pipe (internal).
$567.99
-
Pool Supply Delivery Goulds MFD Rating 161-193 3/4-1 1/2HP Motor Capacitor - 610807 2
This Goulds 610807 2 Motor Start Capacitor makes a high-performance addition to your motor. The non-polarized capacitor is simple to install and use right away. It's constructed from resin or plastic that's resistant to oil and moisture. It has convenient standard dual blade terminals. Dimensions: 1-7/16" x 2-3/4" Product Specifications: Diameter: 1-7/16 in. Length: 2-3/4 in. Volts: 110-125 V Capacitor Microfarad Rating: 161-193 MFD
$31.99
-
Pool Supply Delivery Goulds 1/3 HP 115V 10 ft Cord Sub Sump Pump - LSP0311
Goulds LSP0311 .75 Horsepower 115V 10 ft Cord Submersible Sump Pump is lightweight, portable and easy to service sump pump that is capable of handling up to 3/8" solids. Applications: Basement Draining Water Transfer Dewatering Features: Corrosion-resistant construction Stainless Steel motor casing and fasteners Glass-filled thermoplastic impeller and casing Upper and lower heavy duty ball bearing construction Motor is permanently lubricated for extended service life and is powered for continuous operation. All ratings are within the working limits of the motor. Hard coated 400 series stainless steel shaft for improved corrosion resistance. Float switch is adjustable for various liquid levels. Easily removed for direct pump operation or switch replacement. Complete unit is lightweight, portable and easy to service. A double labyrinth lip seal system protects the motor. It consists of three lip seals and a V-ring in addition to an impeller counterblade system which keeps solid particles away from the seal unit.
$255.99
-
Pool Supply Delivery Goulds 2 HP 1 Phase 230V Centrifugal Self-Priming Pump
Goulds 2 HP 1 Phase 230V centrifugal Self-Priming Pump Goulds 2 HP 1 Phase 230V centrifugal Self-Priming Pump is designed so that once the pump is primed it never needs priming again, even if water level drops below the end of the suction pipe. Pumping resumes once the water level rises above the end of the suction pipe. Specifically designed for lawn sprinkling, irrigation, air conditioning systems, heat pumps, water transfers and dewatering. Pump body has a cast iron casing. Pump has Stainless Steel wear ring for longer life and resistance to wear. Impeller is F.D.A. compliant and glass filled Noryl. Application Water Systems Features: Shaft: Uses Motor shaft, 300 Series Stainless Steel Shaft Seal: Standard Mech. Seal is Buna/Carbon/Ceramic/S.S, Casing "O"-Ring is Buna Ports: 1-1/2" NPT Inlet x 1-1/2" NPT Discharge
$1,091.20
-
Pool Supply Delivery Goulds 1 HP Convertible Jet Pump - J10
The Goulds J10 1.0 Horsepower Convertible Jet Pump is specifically designed for homes, farms, cottages, and booster services. Its convertible design may be used on shallow or deep well applications using appropriate fittings. Serviceable back pullout design allows service without disturbing piping, with a two-compartment motor for access to wiring and replaceable components. It also features a nozzle clean out plug in the shallow well adapter. Corrosion-resistant plastic tubing and fittings are easily removed for cleaning. Premium O-ring design fittings need only be hand tight to seal. Features: F.D.A. compliant Impeller, glass filled Noryl®. Corrosion and abrasion resistant. Bolt down Lexan® diffuser has stainless wear ring for extended performance in abrasive conditions. Pump ratings are within the motor manufacturer’s recommended working limits. Can be operated continuously without damage. Diaphragm retains water in the casing to ensure the mechanical seal can never run dry. After initial priming the pump has the ability to re-prime itself. Electro-coat paint is baked on.
$831.99
-
Pool Supply Delivery Goulds 1 HP 1 Phase 115-230V Centrifugal Self-Priming Pump - GT10
Goulds GT10 1.0 Horsepower 1 Phase 115/230V Centrifugal Self-Priming Pump is designed so that once the pump is primed it never needs priming again, even if water level drops below the end of the suction pipe. Pumping resumes once the water level rises above the end of the suction pipe. Specifically designed for lawn sprinkling, irrigation, air conditioning systems, heat pumps, water transfers and dewatering. Pump body has a cast iron casing, stainless steel ring for longer life and resistance to wear with F.D.A. compliant impeller. Application: Water Systems Features: Shaft: Uses Motor shaft, 300 Series Stainless Steel Shaft Seal: Standard Mech. Seal is Buna/Carbon/Ceramic/S.S, Casing "O"-Ring is Buna Ports: 1-1/2" NPT Inlet x 1-1/2" NPT Discharge
$559.99
-
Pool Supply Delivery Goulds 1 HP 230V 2 Wire Sub w/ CentriPro Motor - 25GS10422C
Goulds 25GS10422C 1.0 Horsepower 230V 2 Wire Submersible Well Pump is powered by a 4" CentriPro motor sized for installation in 4" diameter or larger water wells. Designed with a stainless steel construction for strength and corrosion resistance, this pump model has two cast-in safety line loops for installer convenience. Features: Pump can be operated continuously without damage to the motor Units have left hand threads and are field serviceable with common tools and readily available repair parts Sand handling design Impellers, diffusers and bearing spiders are constructed of FDA compliant glass filled engineered composites. They are corrosion resistant and non-toxic Discharge head/check valve made of cast 303 stainless steel for strength and durability Built-in check valve is constructed of stainless steel and FDA compliant BUNA rubber for abrasion resistance and quiet operation Motor adapter made of cast 303 stainless steel for rigid, accurate alignment of pump and motor Easy access to motor mounting nuts using standard open end wrench Stainless steel casing is strong and corrosion resistant Hexagonal shaft design for positive impeller drive Proprietary engineered polymer bearing is strong and resistant to abrasion and wear Enclosed upper bearing is mounted in a durable Noryl bearing spider for excellent abrasion resistance Two-wire PSC (Permanent Split Capacitor) motor design is quieter than split-phase, 2-wire motors Capacitor reduces pulsation noise Capacitor built-in and hermetically sealed Built-in surge arrestor is provided on single phase motors Stainless steel splined shaft Replaceable motor lead assembly CSA certified UL 778 recognized
$1,167.99
-
Goulds Goulds 5 HP CentriPro 4" 230V 1 Phase 3 Wire Motor - M50412
The Goulds M50412 5.0 Horsepower CentriPro 4" Motor features 305 SS casing and end bells for corrosion resistance, and a stainless steel shaft. This copper wound 4" submersible motor is designed and sized for installation in 4" diameter or larger water wells. This three wire motor has a capacitor start induction run design and requires a control box with a starting relay and capacitor. Specifications: Horse Power - 5 Phase - Single Volts - 230 Motor Type: 3 Wire Features: Stainless steel casing and upper and lower end bells Three-shoe Kingsbury thrust bearing Stainless steel, 17-4 PH splined shaft Removable, replaceable 100 inch motor lead held in place by (2) screws for controlled compression Built-in check valve allows well water to enter motor as needed Surge arrestors built-in CSA Certified, tested to ANSI/NSF 61 NEMA Mounting Dimensions Please note that this 3-wire motor requires a control box Below are Goulds control panel that can be used with this motor: CB50412CR CB50412MC
$1,527.99
-
Goulds Goulds 4" 1 HP 1 Phase 230V 2-Wire Submersible Pump - 25LS10422
Goulds 4" 1 HP 1 Phase 230V 2-Wire Submersible Pump is 230 volts and 8.2 amps. Application: Irrigation Features: 230 volts and 8.2 amps. 2 wire Submersible Pump
$360.00
-
Goulds Goulds 5 HP 230V CentriPro DLX Control Box w/ Magnetic Contactor - CB50412MC
Goulds CB50412MC 5.0 Horsepower 230V CentriPro DLX Control Box has built-in magnetic contactors allow the use of standard pressure switches, prolong switch life and eliminate the need to source and install separate contactors. This will save installation time and reduce total system component cost. Features: Voltage Relay for installer convenience 230 volt standard models Start capacitors for starting torque Run capacitors for efficiency and quiet operation Type N3R enclosure for indoor or outdoor mounting Multiple knockouts and two ground terminals Manual reset overload circuit breakers
$535.99
-
Goulds Goulds 5 HP 85GPM Pump End Assembly - 85GS50
Goulds 85GS50 5.0 Horsepower 85GPM Pump End Assembly is designed with a stainless steel construction for strength and corrosion resistance, this pump has two cast-in safety line loops for installer convenience. This is a pump end only. Motor is not included. e-GS Pump 35-85 Range – (1 – 10 HP) High Capacity Features: Innovative, Proven Hydraulics Up to 13% Efficiency Improvement Fewer models, same hydraulic coverage. Premium Stainless Steel casing, motor adapter, discharge head Built-in Stainless Steel check valve Convenient Serviceability Superior Sand Handling
$1,895.99
-
Goulds Goulds 3/4 HP Shallow Well Pump - J7S
Goulds J7S .75 Horsepower Shallow Well Pump is a compact pump with an integral shallow well adapter built into the casing - which eliminates the need for a separate shallow well adapter. Applications: Homes Cottages Booster Service Features: Shallow Well Adapter Built In Back Pull-Out Design Two Compartment Motor for Easy Access to Wiring Corrosion Resistant Protected Mechanical Seal FDA Compliant Impeller
$727.99
-
Goulds Goulds 4" 1.5 HP 1 Phase 230V 2-Wire Submersible Pump -25GS15422
Goulds 4" 1.5 HP 1 Phase 230V 2-Wire Submersible Pump -25GS15422 Goulds 4" 1.5 HP 1 Phase 230V 2-Wire Submersible Pump is powered for continuous operation and all ratings are within the working limits of the motor. The face clearance, floating impeller stack has proven itself for over 40 years as a superior sand handling, durable pump. The impellers, diffusers and bearing spiders are constructed of glass filled engineered composites. They are corrosion resistant and non-toxic with six sided shafts for positive impeller drive. The built-in check valve is constructed of stainless steel and FDA compliant BUNNA rubber for abrasion resistance and quiet operation. Application: Irrigation Features: Powered for Continuous Operation Field Serviceable Sand Resistant Construction Stainless Steel Metal Parts
$613.60
-
Pool Supply Delivery Goulds 5/8 Shaft Seal - 10K10
Goulds 10K10 5/8 Shaft Seal keeps your Goulds pump in good working condition with proper maintenance and replacement parts. Compatible with: 3642 3742 Cast Iron Bronze Pump Series MCS Stainless Steel Pumps LB Booster Pump Series HSC Centrifugal Pump Series MCC Cast Iron Pumps 316 Stainless Steel Impellers Series GB Booster Pump Series
$23.99
-
Pool Supply Delivery Goulds 3 HP 1 Phase 230V centrifugal Self-Priming Pump
Goulds 3 HP 1 Phase 230V centrifugal Self-Priming Pump Goulds 3 HP 1 Phase 230V centrifugal Self-Priming Pump is designed so that once the pump is primed it never needs priming again, even if water level drops below the end of the suction pipe. Pumping resumes once the water level rises above the end of the suction pipe. Specifically designed for lawn sprinkling, irrigation, air conditioning systems, heat pumps, water transfers and dewatering. Pump body has a cast iron casing. Pump has Stainless Steel wear ring for longer life and resistance to wear. Impeller is F.D.A. compliant and glass filled Noryl. Application Water Systems Features: Shaft: Uses Motor shaft, 300 Series Stainless Steel Shaft Seal: Standard Mech. Seal is Buna/Carbon/Ceramic/S.S, Casing "O"-Ring is Buna Ports: 1-1/2" NPT Inlet x 1-1/2" NPT Discharge
$2,835.00
-
Pool Supply Delivery Goulds 1/3 HP 115V 10 ft Cord Submersible Sump Pump - LSP0311AT
Goulds LSP0311AT .75 Horsepower 115V is lightweight, portable and easy to service filtered effluent sump pump that is capable of handling up to 3/8" solids. Applications: Basement Draining Water Transfer Dewatering Features: Corrosion-resistant construction. Stainless Steel motor casing and fasteners. Glass-filled thermoplastic impeller and casing. Upper and lower heavy duty ball bearing construction. Motor is permanently lubricated for extended service life and is powered for continuous operation. All ratings are within the working limits of the motor. Hard coated 400 series stainless steel shaft for improved corrosion resistance. Float switch is adjustable for various liquid levels. Easily removed for direct pump operation or switch replacement. Complete unit is lightweight, portable and easy to service. A double labyrinth lip seal system protects the motor. It consists of three lip seals and a V-ring in addition to an impeller counterblade system which keeps solid particles away from the seal unit.
$303.99
-
Pool Supply Delivery Goulds 3 HP 1 Phase 230V 3 Wire CentriPro Motor - M30412
Goulds M30412 3.0 Horsepower 230V Three-Wire CentriPro Submersible Motor is designed and sized for the installation in 4 inch diameter or larger water wells. This three wire motor has a capacitor start induction run design and requires a control box with a starting relay and capacitor. Features: Three-Wire – Capacitor Start Motor Design Use with our CentriPro Quick Disconnect or CSCR style control boxes. Laser Welded – 21st century welding technology for improved welds. 700 Lb Thrust Rating – much higher than competitive motors. Precision machined, one-piece, stainless steel castings used for upper and lower end bells. Water-filled design with non-toxic propylene glycol solution to protect the motor during shipping and storage. Built-in check valve allows well water to enter motor as needed. Replaceable motor lead is held in place by (2) screws for controlled compression – no danger of stripping the lead threads. Please note that this 3-wire motor requires a control box. Below are Goulds control panel that can be used with this motor: CB30412CR CB30412MC
$1,103.99
-
Pool Supply Delivery Goulds 23X30 1/2 HP WST PAK w/ WW0511AC - GWP1131
Goulds GWP1131 .50 Horsepower Waste Water Package System is fully assembled at the factory with WW05 Sewage Pump and Ribbed Polyethylene Basin for simplified installation and designed for dewatering wastewater containing solids up to 2". This pump package is ideal for homes, rural water districts, parks, waste drainage in new additions below sewer line or anywhere waste or drainage must be disposed quickly, quietly and efficiently. Features: Eight (8) bolt structural foam cover is strong and corrosion resistant Fully assembled at the factory Ribbed polyethylene basin for strength and durability Schedule 40, 2" pvc discharge pipe with 1/8" bleed hole is factory installed Vent grommets for both 2" and 3" vent provided
$839.99
-
Pool Supply Delivery Goulds 1 HP Shallow Well Pump - J10S
Goulds J10S 1.0 Horsepower Shallow Well Pumps are specifically designed for homes, cottages, and booster services. Its design has an integral shallow well adapter built into the casing, which eliminates the need for a separate shallow well adapter. This pump features a back pull-out design, two compartment motor for easy access to wiring, and is corrosion resistant. Features: Shallow Well Adapter Built In Back Pull-Out Design Two Compartment Motor for Easy Access to Wiring Corrosion Resistant Protected Mechanical Seal FDA Compliant Impeller
$799.99
-
Pool Supply Delivery Goulds 1/3 HP 115V w/ 25 ft Cord Effluent Sump Pump - GSP0311-25
The Goulds GSP0311-25 .75 Horsepower 115V is built with high quality materials to keep you and your basement dry. This submersible sump pump has a cast-iron body that helps dissipate heat as the pump drains water from sump pits. This pump can handle up to 1/2" solids. Features: Premium quality pump Reliable Mechanical switch coupled with solid float for dependable performance Cast Iron Motor Housing allowing for optimal heat dissipation Approved for Residential use (CSA/CUS Listed) Premium Mechanical Seal design provides superior protection against sand and abrasive damage (Silicon Carbide/Carbon/BUNA) Engineered motor designed for peak hydraulic performance without overloading Suction Strainer encompasses entire base – designed to reduce debris entry Corrosion resistant hardware for lifetime use 25 foot cord
$199.99
-
Pool Supply Delivery Goulds 1/2 HP Shallow Well Jet Pump - J5S
Goulds J5S .50 Horsepower Shallow Well Jet Pump is a compact pump with an integral shallow well adapter built into the casing - which eliminates the need for a separate shallow well adapter. Applications: Homes Cottages Booster Service Features: Shallow Well Adapter Built In Back Pull-Out Design Two Compartment Motor for Easy Access to Wiring Corrosion Resistant Protected Mechanical Seal FDA Compliant Impeller
$559.99
You have seen 24 out of 28 products